Детальная информация

Название: Plastic behavior particularities of structures subjected to seismic loads // Magazine of Civil Engineering. – 2021. – № 5 (105). — С. 10513
Авторы: Kabantsev O. V.; Perelmuter A. V.
Выходные сведения: 2021
Коллекция: Общая коллекция
Тематика: Строительство; Строительная механика; building structures; plasticity of structures; seismic loads; combined loads; linear spectral methods; inelastic deformations; строительные конструкции; пластичность конструкций; сейсмические нагрузки; комбинированные нагрузки; линейно-спектральные методы; неупругие деформации
УДК: 624.04
ББК: 38.112
Тип документа: Статья, доклад
Тип файла: PDF
Язык: Английский
DOI: 10.34910/MCE.105.13
Права доступа: Свободный доступ из сети Интернет (чтение, печать, копирование)
Ключ записи: ru\spstu\analitstest\28010

Разрешенные действия: Прочитать Загрузить (0,4 Мб)

Группа: Анонимные пользователи

Сеть: Интернет

Аннотация

For the majority of buildings and structures, the analysis of seismic effects is performed employing the linear-spectral method, and is included into the design regulations of different countries. The linear-spectral analytical method allows for estimating the inelastic deformations in structures by reducing (decreasing) the actual seismic load by means of the coefficient of reduction. The current method of the seismic load reduction corresponds to the elastic-plastic type of structural deformation, with the coefficient of reduction applied to the load-bearing system as a whole. Nonetheless, this deformation pattern is not the only one available. There are structures and structural materials that trigger the elastic-brittle mechanism of transition to the limit state. The constructed buildings and facilities normally contain the structural elements of various deformation patterns (combined structural schemes), and that requires consideration when choosing the calculation method. Employing a universal coefficient of reduction in the design calculations of the combined structural schemes leads to an inaccurate result. Opposite to this, the authors propose herein a solution to the problem of accounting for the joint activity of elastic-plastic and elastic-brittle elements being part of the entire structure based on the energy method. Studied is the combined design model with a single degree of freedom and consisting of elements with different mechanisms of inelastic deformation. Various scenarios of conditions for the joint deformation of heterogeneous elements are analyzed. The general solution to the problem of the coefficient of reduction value for the load-bearing systems made of the elements of different types of inelastic deformation depends on the ratio of stiffness values of the elastic-plastic and elastic-brittle subsystems in structures, as well as on the ratio of bearing capacity of such subsystems. General solutions are obtained to the problem of the maximum permissible value of the coefficient of plasticity for the combined load-bearing system that is responsible for safety of the elastic-brittle sections in structures, and for the system as a whole. When employing the linear-spectral method to calculate the seismic effects for individual parts in structures, it is suggested to use differentiated coefficients of reduction, which is, in fact, complies with the actual performance pattern of structures.

Права на использование объекта хранения

Место доступа Группа пользователей Действие
Локальная сеть ИБК СПбПУ Все Прочитать Печать Загрузить
-> Интернет Все Прочитать Печать Загрузить

Оглавление

  • Plastic behavior particularities of structures subjected to seismic loads
    • 1. Introduction
    • 2. Method
    • 3. Results and Discussion
      • 3.1. Mechanisms of transition into limit state and impact thereof on structures
      • 3.2. Limit values of the coefficient of plasticity
    • 4. Conclusion

Статистика использования

stat Количество обращений: 84
За последние 30 дней: 4
Подробная статистика