Table | Card | RUSMARC | |
Allowed Actions: –
Action 'Read' will be available if you login or access site from another network
Action 'Download' will be available if you login or access site from another network
Group: Anonymous Network: Internet |
Annotation
Целью работы является исследование и проектирование операционного усилителя на дискретных элементах. При выполнении цели сначало необходимо учитывать идеальные параметры операционного усилителя. Например: коэффициент усиления, входное и выходное сопротивления, входной ток и АЧХ. Потом было выполнено моделирование и анализы ОУ с помощью среды Micro-Cap. А также увидели, что за счет общей линейности усилителя, при введении обратной связи, у нас получается очень линейный усилитель в которовм можно выполнять частотную коррекцию, меняя ёмкость С4. С помощью ОС ограничили полосу до 27 кГц, т.к. используем наш усилитель для усиления звука. Не мало важным является вид спектра гармоник. У нас главные 2 и 3 гармоники. чем ниже гармоника, тем лучше. Проведённое моделирование показало, что параметры ОУ хорошие и лучше чем в интегральных схемах. B частности коэффициент нелинейных искажений меньший (0.02%). После выполнения моделирования и получения результатов анализов, была получена макетная плата для проверки параметров ОУ. Затем в сервисе «Easyeda» создали печатную плату усилителя. Используя онлайн сервис «Easyeda» можно довольно просто спроектировать печатную плату и заказать ее изготовление. В ходе работы проверили, что ОУ можно собирать на дискретных компонентах. Провели сборку печатной платы и проверили работоспособность устройства. Мы сделали хороший операционный усилитель (по качестве и по цене).
The aim of the work is to research and design an operational amplifier on discrete elements. When fulfilling the goal, it is first necessary to consider the ideal parameters of the operational amplifier. For example: gain, input and output resistances, input current and frequency response. Then, simulation and analysis of the opamp using the Micro-Cap medium was performed. And we also saw that due to the general linearity of the amplifier, with the introduction of feedback, we get a very linear amplifier in which frequency correction can be performed, changing the capacity of C4. Using the OS, they limited the band to 27 kHz, because We use our amplifier to amplify the sound. Equally important is the form of the harmonic spectrum. We have the main 2 and 3 harmonics. the lower the harmonic, the better. The simulation showed that the parameters of the op-amp are good and better than in integrated circuits. In particular, the non-linear distortion coefficient is lower (0.02%). After performing the simulation and obtaining the results of the analyzes, a breadboard was obtained for checking the parameters of the op-amp. Then, the “Easyeda” service created an amplifier circuit board. Using the online service "Easyeda" you can quite simply design a printed circuit board and order its manufacture. In the course of work, we checked that the op-amps can be assembled on discrete components. We carried out the assembly of the printed circuit board and checked the operability of the device. We made a good operational amplifier (in quality and price).
Document access rights
Network | User group | Action | ||||
---|---|---|---|---|---|---|
ILC SPbPU Local Network | All | |||||
Internet | Authorized users SPbPU | |||||
Internet | Anonymous |
Usage statistics
Access count: 2
Last 30 days: 0 Detailed usage statistics |