Table | Card | RUSMARC | |
Allowed Actions: –
Action 'Read' will be available if you login or access site from another network
Action 'Download' will be available if you login or access site from another network
Group: Anonymous Network: Internet |
Annotation
В данном выпускной работе была спроектирована электрическая часть КЭС на газомазутном топливе с генераторами мощностью 4*800 МВт. Основные задачи, которые были разрешены в процессе проектирования: 1. Выбор структурной схемы станции, основного оборудования (генераторы, трансформаторы, автотрансформаторы, выключатели, разъединители). 2. Расчет токов короткого замыкания в типовых точках электрической части станции. 3. Выбор токоведущих частей (кабели, шины, экранированные токопроводы). 4. Выбор измерительных приборов и трансформаторов тока и напряжения. 5. Подробный расчет и анализ системы собственных нужд. 6. Разработка чертежей главной схемы электрических соединений станции и компоновки одного из распределительных устройств. В ходе работы выбор основного оборудования был осуществлен с опорой на технико-экономический анализ структурной схемы, который позволил принять наиболее выгодное решение. Расчет токов короткого замыкания являлся неотъемлемой частью работы. Он помог осуществить проверку выбранного оборудования по условиям продолжительной работы в нормальном режиме, на термическую и электродинамическую стойкость при коротких замыканиях. Измерительные трансформаторы тока были проверены по вторичной нагрузке, а трансформаторы напряжения на потери напряжения в цепях с измерительными проборами. Результатом работы является проект электрической части КЭС, включающий пояснительную записку с обосновывающими расчетами, чертежи главной схемы электрических соединений КЭС и конструкции распределительного устройства 220 кВ.
In this final work the electrical part of the condensate power plant on gas-oil fuel with generators with a capacity of 4*800 MW was designed. The main tasks that were solved during the design process: 1. Selection of the structural scheme of the station, the main equipment (generators, transformers, autotransformers, switches, disconnectors). 2. Calculation of short-circuit currents at typical points of the electrical part of the station. 3. The choice of current-carrying parts (cables, busbars, shielded current lines). 4. The choice of measuring devices, current transformers and voltage transformers. 5. Detailed calculation and analysis of the system of own needs. 6. Development of drawings of the main circuit of the electrical connections of the station and the configuration of one of the switchgear. In the course of the work, the choice of the main equipment was carried out based on the technical and economic analysis of the block diagram, which allowed us to make the most profitable decision. The calculation of short-circuit currents was an integral part of the work. It helped to check the selected equipment under the conditions of long-term operation in normal mode, for thermal and electrodynamic endurance in case of short circuits. Measuring current transformers were tested for secondary load, and voltage transformers for voltage losses in circuits with measuring parting. The result of the work is a project of the electrical part of the power plant, including an explanatory note with justifying calculations, drawings of the main circuit of the electrical connections of the power plant and the design of the 220 kV switchgear.
Document access rights
Network | User group | Action | ||||
---|---|---|---|---|---|---|
ILC SPbPU Local Network | All | |||||
Internet | Authorized users SPbPU | |||||
Internet | Anonymous |
Usage statistics
Access count: 32
Last 30 days: 0 Detailed usage statistics |